Community C6 6.5" 2-Way, Full Range Ceiling Loudspeaker, White

The Commercial Design C6 provides high quality paging and musical performance. Uniform voicing throughout the Commercial Design Series means that the C6 can be combined with other models of the Commercial Design Series without compromising consistency from zone to zone. Community’s proprietary Tru-Phase™ waveguide produces a consistently wide conical polar response up to 16 kHz. The genuine coaxial design uses separate magnets for the LF and HF drivers for reduced distortion and industry-leading sensitivity, thereby permitting up to 3 dB greater output level while requiring up to half the amplification power of competing products. Exclusive Drop-Stop™ tabs allow single-handed placement to speed installation and reduce labor time. Drop-Stop’s spring-loaded legs support the back can so that the installer no longer needs to hold the can against the tile while tightening the clamps. The front-face wattage selector switch enables quick adjustment of 70V/100V tap levels.

• High intelligibility with exceptional uniform coverage
• Consistent, wide dispersion up to 16 kHz
• True coaxial loudspeakers with HF compression drivers
• Tru-Phase™ high-frequency waveguide
• Spring loaded Drop-Stop™ installation assistant tabs support the back can on the included rails simplify installation
• Uniquely designed tile bridge support rails prevent ceiling tile sagging
• External loop-through Euroblock connectors
• Rear cover with integrated cable clamp (strain relief) and optional conduit knockout
• Face-mounted adjustable tap position selector switch
• Selectable 8 ohm or 70V/100V operation

Loudspeaker Type

• Two-way, full-range, coaxial ceiling loudspeaker, 8 ohm or 70V/100V operation

Operating Range

• 70 Hz - 13.5 kHz (-10 dB)

Frequency Response

• 115 Hz - 12.5 kHz (-3 dB)

Max Input Ratings (8 ohm)

• 60W continuous, 150W program
• 21.9 volts RMS, 43.8 volts momentary peak

Transformer Taps

70V

• 30W, 15W, 7.5W, 3.75W, and 8 ohm selectable

100V

• 30W, 15W, 7.5W, and 8 ohm selectable

Distortion—10% Full Power

2nd Harmonic

• 500 Hz: 0.33%
• 2 kHz: 1.11%
• 8 kHz: 2.49%

3rd Harmonic

• 500 Hz: 0.55%
• 2 kHz: 0.80%
• 8 kHz: 0.21%

Distortion—1% Full Power

2nd Harmonic

• 500 Hz: 0.25%
• 2 kHz: 0.67%
• 8 kHz: 0.30%

3rd Harmonic

• 500 Hz: 0.06%
• 2 kHz: 0.23%
• 8 kHz: 0.06%

Sensitivity (1W/1m)

• 91 dB SPL (125 Hz to 12.5 kHz 1/3 octave bands)
• 91 dB SPL (250 Hz to 4 kHz speech range)

Maximum Output 

• 8Ω: 109 dB SPL / 115 dB SPL (peak)
• 70V: 106 dB SPL / 112 dB SPL (peak)
• 100V: 106 dB SPL / 112 dB SPL (peak)

Nominal Impedance

• 8 ohms

Minimum Impedance

• 7 ohms @ 10 kHz

Nominal Coverage

• 120º conical (1 kHz to 6 kHz ±65°)
• 120° conical (500 Hz to 6 kHz ±65°)

Axial Q / DI

• 4.9/6.9, 500 Hz to 6 kHz

Crossover Frequency

• 2 kHz

Recommended Signal Processing

• 100 Hz, at 24 dB per octave high pass filter

Drivers

• LF 1 x 6.5-inch cone
• HF 1 x ¾-inch exit compression driver

Driver Protection

• Self-resetting solid state circuit breaker

Input Connection

• 4-pole Euroblock connector with two pair of non-interrupt parallel connections

Controls

• Front-face wattage / low impedance selector switch

Enclosure

• Corrosion-resistant zinc plated steel

Finish

• White or black

Mounting/Rigging Provisions

• 2 ABS mounting clamps with 1.75-inch grip range

Grille

• Powder coated steel with safety line, white or black finish, paintable

Safety Features

• 2 x safety hang points

Safety Agency Ratings

• ETL listed to comply with UL1480, UL2043 and CSA60065. Suitable for use in air handling spaces per NFPA 70 and NFPA 90.

Required Accessories

• Electronic high pass filter

Dimensions 

• Width: 9.80 inches (248.9 mm) bezel diameter
• Depth: 6.49 inches (164.8 mm) can depth

Weight

• 7.1 lbs (3.2 kg)

Baffle

• Reflex loaded UL 94V-0 rated ABS

Cutout Diameter

• 8.86 inches (225 mm)