Meyer Sound USW-112P Compact Narrow Subwoofer

DISCREET SYSTEM ENHANCEMENT

The USW-112P self-powered subwoofer delivers powerful low-frequency performance in a compact, versatile package. It’s designed as an ideal companion for ULTRA‑X20 loudspeaker and complements a range of Meyer Sound loudspeakers including the UPM, UP‑4slim, Ashby‑5C, and Ashby‑8C. Its low-profile cabinet measures just 23.5 inches high by 13.5 inches wide by 12 inches deep, making it an ideal choice when space is limited.

LEAN-AND-CLEAN LOW END

Count on the USW-112P to deliver clean, low-distortion output at any output level: Its proprietary 12” low-distortion, long-excursion driver enhances low-frequency performance in the 35 to 140Hz range, and its cabinet incorporates a low-air-velocity port tuned for high efficiency, linear response, and low distortion.

POTENT PROCESSING

The USW-112P’s built-in Class D amplifier delivers a linear peak SPL of 123 dB, measured using M‑Noise. Sophisticated signal processing includes electronic crossover, correction filters for phase and frequency response, and driver-protection circuitry. The crossover accepts full-range signals, enabling daisy-chain signal distribution and eliminating the need for external crossovers in smaller systems.

AGILITY PLUS STABILITY

The 47-pound USW-112P fits anywhere, from churches and clubs to restaurants and small theatres. Orient it in horizontal or vertical position; its two integrated M8 mounting points can be used with an optional U-bracket to enable wall, ceiling, or truss mounting. Other options include a 35mm stand-mount receptacle with M20 threads for added stability.

Acoustical

• Operating Frequency Range: 35 Hz – 140 Hz
• Frequency Response: 36 Hz – 125 Hz ± 4 dB
• Phase Response: 45 Hz – 120 Hz ±30°
• Linear Peak SPL: 123 dB with > 10.5 dB crest factor (M-noise), 123 dB (Pink Noise), 125 dB (B-noise)

Transducer

• Low Frequency: One 12-inch cone driver; 3 Ω nominal impedance

Audio Input: Analog

• Type: Differential, electronically balanced
• Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient
  protection
• Connectors: XLR 3-pin female input with male loop output; optional XLR 5-pin connector to accommodate both balanced audio and RMS signals; XLR 3-pin TOP (Total Outdoor Protection) connectors on weather-protected units only
• Input Impedance: 10 kΩ differential between Audio(+) and Audio(-)
• Wiring: Pin 1: Chassis/earth through 1 kΩ, 1000 pF, 15V clamp network to provide virtual ground lift at
  audio frequencies / Pin 2: Audio + / Pin 3: Audio / Pin 4: RMS (polarity insensitive) / Pin 5: RMS (polarity insensitive) / Case: Earth ground and chassis
• Nominal Input Sensitivity: 0 dBV (1.0 V rms) continuous is typically the onset
  of limiting for noise and music
• Input Level: Audio source must be capable of producing of +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.

Audio Input: Digital

• Connectors: etherCON TOP
• Digital Format: Milan Certified

Amplifier

• Type: Open-loop, Class-D
• Total Output Power: 1200 W peak
• THD, IM, TIM: < 0.02%
• Cooling: Convection

AC Power

• Connector: powerCON 20 input with loop output; powerCON TRUE1 TOP with loop output on digital and weather-protected units
• Automatic Voltage Selection: 90–265 V AC, 50–60 Hz
• Safety Rated Voltage Range: 100–240 V AC, 50–60 Hz
• Turn-on and Turn-off Points: 90 V AC turn-on, no turn-off; internal fuse protection above 265 V AC

Current Draw

• Idle Current: 0.23 A rms (115 V AC); 0.18 A rms (230 V AC); 0.25 A rms (100 V AC)
• Maximum Long-Term Continuous Current: (>10 sec) 1.2 A rms (115 V AC); 0.7 A rms (230 V AC); 1.4 A rms (100 V AC)
• Burst Current: (<1 sec)8 3.6 A rms (115 V AC); 1.8 A rms (230 V AC); 4.1 A rms (100 V AC)
• Maximum Instantaneous Peak Current: 8.9 A peak (115 V AC); 4.5 A peak (230 V AC); 10.3 A peak (100 V AC)
• Inrush Current: < 20 A peak

Remote Monitoring: Analog

• Optional RMS module: two-conductor twisted-pair
  network that reports all operating parameters of
  amplifiers to system operator’s host computer via
  the RMServer hardware unit

Remote Monitoring: Digital

• Integrated monitoring via Compass Control
  Software

Physical

• Dimensions: W: 13.5 in (343 mm) x H: 23.5 in (597 mm) x D: 12 in (305 mm)
• Weight: 45 lb (20 kg)
• Enclosure: Premium multi-ply birch with slightly textured black finish
• IP Rating: Weather-protected version rated IP54. See the USW-112P Operating Instructions available at meyersound.com/documents for details
• Protective Grille: Powder-coated, round-perforated steel
• Rigging: Two integrated M8 threaded points; 35 mm Pole Mount with M20 thread; optional U-bracket for wall, ceiling, or truss mounting